Table of Contents
The Scag Tiger Cat 2 lawn mower is one of the most influential and durable machines in its price range. It comes with a cutting deck of 54 inches that provides you with enough area to cover in just one pass. The engine is powerful enough to cut through tough grass, leaves, and weeds. The 27 hp engine will provide enough power for mulching or bagging your grass clippings.
The Scag Tiger Cat 2 features a 5-speed transmission system ranging from 1-5 speeds. This allows you to adjust the speed depending on the terrain you are cutting through. In addition, an adjustable handlebar allows you to change the height of the machine depending on how tall you are.
The engine Will Not Turnover or Start
If the starter has failed or the battery is dead, you have a problem that can be solved with a jump-start. If the starter works, but the engine won’t crank, you have a bad ignition switch or one of its electrical connections. The ignition switch is on top of your steering column; you’ll need to remove the plastic airbag cover and airbag to get at it.
If your key doesn’t turn in the ignition, ensure you’re using the right key. If you still can’t get it to move, take off the steering wheel and see if there’s any play in it—if so, replace it with a new one.
If nothing works except for the headlights coming on when you turn the key on (and they go off when you turn it off), then chances are good that your battery is just about dead and needs to be replaced.
The engine will not turn over or start:
- Check the battery terminals and connections. Make sure there are no loose connections or corrosion. If you have a voltmeter, check that the voltage is above 12 volts at the battery terminals. If it is not, charge or replace the battery.
- Remove and clean any debris around the spark plugs, especially if they have been changed recently. Also, check the spark plug gap (between 3/8 and 1/4 inch) and make sure there is no oil or grease on top of them. Also, inspect the distributor cap and rotor for cracks or breaks in their insulation material. Replace as necessary.
- Verify that all fuses are operational. Replace any that have blown out with new ones of the same amperage rating (see chart in owner’s manual). Only use oversized fuses specified – this can damage electrical components such as your starter solenoid!
- Remind one spark plug wire from its spark plug at a time and check for spark by grounding its end against a metal part of your engine block (such as an intake manifold bolt). Do this with all four wires in turn – if there is no spark on any of the cylinders, the problem is not with a faulty coil but somewhere else in the ignition system.
- If there is a spark, but the engine still won’t start, then you should check the fuel system for leaks or other problems. If it starts but runs roughly (especially when cold), you may have air in the fuel system. If it runs fine at idle but stalls when revved up to speed, this could be due to a blocked fuel filter or dirty injectors.
Cutting Speed Issue In SCAG Tiger Cat 2
SCAG Tiger Cat 2 is a mowing machine with a cutting speed of up to 15 miles per hour. The mower comes with two blades that are made from steel and have sharpened edges. The blades work together to deliver a clean and smooth finish.
If the cutting speed of your mower is not working as it should, here are some common causes:
Blade is Dull
If you are experiencing slow cutting speed, then it could be due to the blade being dull. You can easily check whether this is the case by cutting grass using both blades together. If there is a difference in speed between these two blades, then one of them is dull and needs sharpening or replacing.
Blade Is Damaged
Another reason your mower may need help with its cutting speed is damage in one of its blades. This can happen when you hit something while mowing, like an object or another object that was hidden under the grass or other plants. When this occurs, one side of your blade will be damaged or bent out of shape, making it harder to cut through vegetation smoothly and evenly on both sides.
Fuel Filter Problems in Scag Tiger Cat 2
The fuel filter is a part of your engine that catches any particles or debris in the fuel. The fuel filter must be replaced every so often, depending on how much you drive and how well you take care of your vehicle. If you notice that your car is running rough or having difficulty starting, it could be time to replace your fuel filter.
Symptoms of a Bad Fuel Filter
Several symptoms can indicate that your fuel filter needs to be replaced. These include:
Rough idle – When you start the car, there may be a hesitation before the engine starts running smoothly. This is a sign that debris may clog up your fuel system.
Hard starting: If the car has trouble starting, this could be due to a lack of power from the fuel pump or clogging from dirty fuel. A bad or dirty fuel filter can cause this problem, as well as damaged or worn-out spark plugs, which will prevent proper ignition timing.
Poor performance: If it seems like your car has lost some power compared to when it was new, this could be due to not replacing your filters regularly or using low-quality gas that doesn’t provide enough lubrication for parts like valves and pistons, which can lead to damage over time.
Poor acceleration: If you have trouble accelerating, you may have a bad fuel filter. If the filter is clogged or full of gunk, it can cause the engine not to receive enough fuel or air, resulting in poor acceleration.
Hard starting: If your engine starts hard when cold, this could be due to a clogged air filter, low-quality fuel, or dirty spark plugs.
Engine oil leak: Engine oil leaks are usually caused by a worn-out gasket seal between the valve cover, cylinder head, and other gaskets around these components. This causes oil to leak out, which can cause problems with internal engine parts over time.
Defective Ignition Switches in Scag Tiger Cat 2
The ignition switches in the Scag Tiger Cat 2 are defective and may cause the mower to stall while you are mowing. These switches fail because they are made from cheap plastic, which is not durable enough for the high-temperature environment of a lawnmower engine. The problem with this defect is that it is not visible until after the ignition switch fails, so if your ignition switch has failed and your mower will not start, you will need to replace it.
An authorized Scag dealer or a certified technician should replace the Ignition Switch on the Scag Tiger Cat 2. If you replace this part yourself, you may damage other components of your mower during installation.
Mower Get Out Of Control in Scag Tiger Cat 2
If your Scag Tiger Cat 2 starts running out of control while cutting your lawn, there may be something wrong with the fuel filter or carburetor jets. You should check these parts before doing anything else because they can be easily replaced if worn out or damaged.
If your Scag Tiger Cat 2 stops while you’re cutting the lawn, it could be due to low oil levels. You should check this before you do anything else because low oil levels can cause severe damage to your engine and other parts of your mower.
Belt Misalignment in Scag Tiger Cat 2
The issue with the Scag Tiger Cat 2 mower is that the belt tends to come off track. In this case, it may be because of belt misalignment. This can happen when you need to adjust and tighten the belts properly. The belt must be centered on pulleys so that it does not slip off track or move from its position. This problem can be solved by checking if the belt is seated correctly on the pulleys and the drive belt tensioner is working properly. If there is still a problem, you may need to replace your drive belt or pulleys.
The other possible cause for this problem is worn-out parts in your mower’s drive system. These include worn-out bearings, bushings, and worn-out bearings in your wheel hubs or wheel bearings. In this case, you will need to replace these worn-out parts before using your mower again.
Hard Starting or Poor Engine Running in Scag Tiger Cat 2
If your engine is hard to start or runs poorly, there could be several reasons for this. It could be due to an issue with carburetor jetting (how much fuel gets pumped into the engine), spark plug fouling (which causes misfires), ignition timing (the time at which the spark plug fires), or other types of issues.
Before diagnosing and fixing problems, ensure gas gets through to the carburetor by checking for fuel lines or hoses leaks. If there are no leaks, check your pull cord for fraying or damage — if it looks worn out, replace it immediately before using the mower again, so it doesn’t break off while in use.
Problems with Hydro Belt in Scag Tiger Cat 2
The hydro belt is a common problem on the Scag Tiger Cat 2. This belt drives the power steering pump and is also used to drive various other components. Over time, this belt will break, causing the power steering pump to fail and leaving you without power steering. The failure usually occurs while driving on uneven terrain or turning sharply at high speeds.
Design Flaw
The most common cause of these failures is a design flaw in the hydro belt itself. The belt is made up of two pieces that are riveted together. When these two pieces separate, they can be challenging to re-attach properly and may even cause more damage if not repaired properly.
Heat Buildup Or Dust
The most common cause of this issue is heat buildup inside the engine compartment or if there is too much dust buildup on top of the belt.
Excessive Mower Vibration In Scag Tiger Cat 2
One common problem with the Scag Tiger Cat 2 is excessive vibration. If you are experiencing this issue, you should check your tires to ensure they are properly inflated and balanced. If they are not, this can cause excessive vibration in your mower. You may also need to have your blades sharpened or replaced if it turns out they are dull and causing excessive vibration in your machine.
The Scag Tiger Cat 2 Has A Slow Blade Rotation Speed
The Scag Tiger Cat 2 is a high-quality machine with an engine that can deliver much power. However, one thing you might notice about this machine is its slow blade rotation speed. This means that the blades are rotating slowly compared to other machines on the market.
This issue will be fine if you use this machine for commercial use. But if you are using it for home use, look at another machine with a faster blade rotation speed.
The Scag Tiger Cat 2 Has A High Noise Level
The noise level of a Scag Tiger Cat 2 can be affected by several factors, such as engine noise, cutting blade noise, and vibration noise. While some noise is expected from a commercial-grade mower, excessive noise can concern operators and those in the surrounding area.
Here are some potential reasons why the Scag Tiger Cat 2 may have a high noise level:
- Worn or damaged blades: Over time, the cutting blades on a mower can become dull or damaged. This can cause the blades to produce more noise than usual as they cut through the grass.
- Loose or worn belts: Loose or worn belts can cause vibration and noise in the mower. Belts should be inspected regularly and replaced when necessary.
- Engine condition: The condition of the engine can also affect the noise level of the mower. If the engine is not running smoothly or has worn parts, it may produce more noise than usual.
- Poor maintenance: Lack of regular maintenance, such as changing the oil, air filter, and spark plugs, can cause the engine to work harder and produce more noise.
Regular maintenance and inspections should be performed to reduce the noise level of the Scag Tiger Cat 2. Replace any worn or damaged parts and ensure that the blades are properly sharpened and balanced. Additionally, using hearing protection while operating the mower can help to protect the operator’s ears from excessive noise.
The Scag Tiger Cat 2 Has A High Vibration Level
Excessive vibration on the Scag Tiger Cat 2 can concern operators. It can lead to operator fatigue, discomfort, and even long-term health issues like hand-arm vibration syndrome. Several factors, such as unbalanced cutting blades, worn or damaged parts, or improper maintenance, can cause high vibration levels. Here are some potential reasons why the Scag Tiger Cat 2 may have a high vibration level:
- Unbalanced cutting blades: Unbalanced cutting blades can cause excessive vibration when the mower is in use. This can occur due to damage, wear, or improper sharpening of the blades.
- Worn or damaged parts: Worn or damaged parts, such as belts, pulleys, or bearings, can cause excessive vibration. These parts should be inspected regularly and replaced when necessary.
- Improper maintenance: Lack of regular maintenance, such as oil changes or filter replacements, can cause the engine to work harder, leading to increased vibration.
- Uneven terrain: Mowing on rough terrain can cause the mower to vibrate more than usual. In such cases, it may be necessary to adjust the cutting height or mow at a slower speed.
Regular maintenance and inspections should be performed to reduce the vibration level of the Scag Tiger Cat 2. It is also beneficial to balance the cutting blades and replace any worn or damaged parts. Additionally, operators can adjust the mowing speed or cutting height to reduce vibration on uneven terrain. Using anti-vibration gloves or adding vibration-dampening materials to the handles can also help to reduce the amount of vibration transferred to the operator’s hands and arms.
The Scag Tiger Cat 2 Has Blade Special Issues
The Scag Tiger Cat 2 has some problems with the blade that you need to be aware of before you buy this mower. The blade is steel and will only hold up well if you take care of it properly. If you do not maintain this mower, then you are going to be faced with some issues down the road.
One problem with this mower is that the blades will rust if wet. If you have an older house with many trees around it, chances are good that your yard will get wet at one point or another during the year. If this happens, there could be problems when you try to start your mower up again in the springtime or after winter.
The Scag Tiger Cat 2 Has Starting Issues
If your mower starts but stalls after a few minutes and won’t start again until it cools down, then you likely have overheated spark plugs from running too hard for too long. This will cause them to foul out and not fire properly when hot due to residual oil from previous use or even being old (which can happen after just a couple of years). If this happens and you let it cool down for about 10 minutes or so before trying again, the plugs should fire up fine again until they get hot enough again and foul out again.
If the Scag Tiger Cat 2 is experiencing starting issues, there are several possible reasons for this. Here are some potential causes:
- Battery issues: If the battery is weak or dead, the engine may not start. The battery should be checked and replaced if necessary.
- Dirty or clogged air filter: A dirty or clogged air filter can prevent the engine from getting the air it needs to run properly. The air filter should be inspected and cleaned or replaced as needed.
- Fuel issues: If the fuel is old, contaminated, or not reaching the engine properly, the engine may not start. The fuel system should be inspected, and the fuel filter should be replaced if necessary.
- Spark plug issues: A fouled or worn spark plug can prevent the engine from starting. The spark plug should be inspected and replaced if necessary.
- Faulty ignition switch: If the ignition switch is faulty, the engine may not start. The switch should be inspected and replaced if necessary.
To troubleshoot starting issues with the Scag Tiger Cat 2, you should check the battery and ensure it is properly charged. You should also check the air filter, fuel system, and spark plug. If these components appear in good working order, you may need to have the ignition switch inspected or tested. It is important to follow the manufacturer’s recommendations for maintenance and service to ensure that the mower is running properly. If you are not comfortable performing these checks or repairs yourself, it is recommended to seek the assistance of a trained technician.
Let’s compare the features of Scag and Gravely.
Conclusion
In this article, we told you about the Scag tiger cat’s two problems. If your Scag tiger cat two has problems with its battery or fuel filter, get it serviced as soon as possible. You should also check the spark plugs, especially if your Scag tiger cat 2 is five years old and hasn’t had regular maintenance on its ignition switch.
However, how the machine is used, maintained, and adjusted affects how long it lasts. This machine can last you for many years if you are aware of the issues and fix them in time. So keep checking your machine if it does not have any problem because, in this case, you might catch some problem at the initial stage, which saves upcoming damage.
Related Posts
